CE 78 Jointing Filler 4h
Indoor plasterboard
Jointing filler
ADVANTAGES
- No synthetic resins
- 500 times lower voc emissions than the a+ threshold
- Excellent joint finish
TECHNICAL DEFINITION
This powder filler is designed specifically for jointing tapered edge plasterboard in combination with joint tape.
This powder filler is designed specifically for jointing tapered edge plasterboard in combination with joint tape.
TECHNICAL CHARACTERISTICS
- Ahdesion: Tape adhesion: > 1,000 g
- Cracking: No cracking up to a thickness of 5 mm.
- Reaction to fire: A1
- Setting time: 4 h
PACKAGING
5 and 25 kg bags
5 and 25 kg bags
COMPOSITION
Marble powder, natural plaster, starch and cellulose.
Does not contain synthetic resin.
The paste obtained is cream coloured.
Marble powder, natural plaster, starch and cellulose.
Does not contain synthetic resin.
The paste obtained is cream coloured.
SUITABLE SUBSTRATES
All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and paper surfaces.
All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and paper surfaces.
STORAGE
9 months in original, unopened packaging protected from damp.
9 months in original, unopened packaging protected from damp.
SUBSTRATE PREPARATION
Plasterboard must be attached in compliance with DTU 25.41 or 25.42.
Cuts made in boards must be bevelled and dust-free.
Plasterboard must be attached in compliance with DTU 25.41 or 25.42.
Cuts made in boards must be bevelled and dust-free.
MIXING RATIO
10 to 11 L of water per 25 kg bag.
2 to 2.2 L of water per 5 kg bag.
2 volumes of water for 5 volumes of powder.
10 to 11 L of water per 25 kg bag.
2 to 2.2 L of water per 5 kg bag.
2 volumes of water for 5 volumes of powder.
USE
Before commencing jointing work, fill any accidental gaps between boards and repair any damage (spalling, damaged surface, etc.).
Apply manually using a 10 or 15 cm jointing knife and apply the tape (rough side against the filler). Apply a finish coat, leave to dry and finish to hide the tape.
Also hide any screw heads.
Apply tape to ceiling joints, ensuring that there is no formwork oil on the concrete.
For vertical outside corners, use reinforced tape (reinforced side against the board) or a metal corner bead.
Before commencing jointing work, fill any accidental gaps between boards and repair any damage (spalling, damaged surface, etc.).
Apply manually using a 10 or 15 cm jointing knife and apply the tape (rough side against the filler). Apply a finish coat, leave to dry and finish to hide the tape.
Also hide any screw heads.
Apply tape to ceiling joints, ensuring that there is no formwork oil on the concrete.
For vertical outside corners, use reinforced tape (reinforced side against the board) or a metal corner bead.
DRYING TIME
A second coat can be applied 6 to 8 hours after the application of the first coat.
A second coat can be applied 6 to 8 hours after the application of the first coat.
CONSUMPTION
Approximately 350 g/m² of plasterboard.
Approximately 350 g/m² of plasterboard.
COVERING
Primer undercoat for plasterboard.
Plaster-based or ready-to-use smoothing compound.
Primer undercoat for plasterboard.
Plaster-based or ready-to-use smoothing compound.
AVAILABLE DOCUMENTATION
DTU 25.41 and DTU 25.42
NF EN 13963.
CE marking
DTU 25.41 and DTU 25.42
NF EN 13963.
CE marking
PRÉCAUTIONS_DEMPLOI
The temperature during application and drying must be between 5 and 30°C.
Do not apply to damp substrates.
Do not use mix that has started to set.
The temperature during application and drying must be between 5 and 30°C.
Do not apply to damp substrates.
Do not use mix that has started to set.
Semin on
social media
